![qunqi l298n motor driver qunqi l298n motor driver](https://www.navestar.com/wp-content/uploads/2019/12/L298N-Motor-Drive-Controller-Board-Module-dual-H-Bridge-DC-Stepper-Motor-Driver-4.jpg)
The diagram below shows all the components consisting inside the module.
Qunqi l298n motor driver driver#
2 large terminal external power terminals, to ensure logicĨ. The L298N motor driver module consists of a L298N motor driver IC ,78M05 5V regulator, 5V jumper enable, power LED, heat sink, resistors and capacitors all combined in an integrated circuit. Large terminal blocks make wiring easier (10-22AWG) and powerħ. Qunqi L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper for Arduino Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip.Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors. The pull-down resistor ensures that the motor remains stoppedĥ. Qunqi L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper For Arduino Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip.Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors. 4-way H-bridge: The L293D chip provides 0.6A (peak 1.2A)Ĭurrent per bridge with thermal shutdown protection, 4.5Vto36VĤ. For more details the datasheet given to the below link. It uses the popular L298N Dual H-Bridge Motor Driver chip and is powerful enough to drive motors from 5-35 Volts at up to 2 Amps per channel. It is a high voltage, a high current dual full-bridge driver designed to accept standard TTL logic levels. The L298N Dual H-Bridge Motor Driver is a low cost motor driver board that can be used to drive two robot motors. which is an integrated monolithic circuit in a 15-lead Multiwatt package. Up to 2 stepper motor forward and reverse control, single /ĭouble step control, staggered or micro-step and rotation angleģ. An L298N motor driver module consists of an L298N motor driver chip(IC). to 4 bidirectional DC motors and 4 PWM speed controllersĢ. Qunqi 2Packs L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper For Arduino Specification: Chip: L298N Logic voltage: 5V Logic current 0mA.
![qunqi l298n motor driver qunqi l298n motor driver](https://i2.wp.com/dronebotworkshop.com/wp-content/uploads/2017/02/L298-Motor-Control-Module-Arduino-Potentiometers-e1504972437694.jpg)
![qunqi l298n motor driver qunqi l298n motor driver](https://m.media-amazon.com/images/I/61VkNn0PcaL._AC_SS450_.jpg)
Tested compatible for Arduino Mega, Diecimila & Duemilanove.Using this chip you can use DC motors and power supplies of up to 10 Volts, that some pretty big motors and the chip can supply a maximum current of 600mA per channel.This is a commonly used DC motor drive module, using a small current 293 chip DC motor driver chip.Angrenaj Rou Muscular Qunqi L298N Motor Drive Controller Board Module. This module has a built-in 5v power supply, when the driving voltage is 7v-35v, this supply is suitable for power supplyĭO NOT input voltage to +5v supply interface, however ledding out 5v for external use is available. Bourul anxietate Arte literare L298 Module Red Board (Dual H-bridge motor driver. Large capacity filter capacitance,afterflow protection diode, more stable and reliable.High working power to 46v,large current can reach 3A MAX and continue current is 2A, power to 25w.Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability.To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, ST corporation production.Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.Qunqi 2Packs L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper For Arduino 4 Kinds Dc L298n Motor Driver Module Stepper Motor Dual H Bridge For.